High Solids Euro Clear By Tamco
Tamco Logo. One of the quality wet paints shipped free by Paint With Pearl.

HC-2104 2:1 Euro Clear Tamco High-Solids UV Clear Topcoat

$180.00 $160.00

Free Shipping! HC-2104 Euro- Clear- The best clear money can buy!  – at a fraction of the cost.

A beautiful HIGH GLOSS European style clear. Very High Solids and cures much more quickly than “cheaper” Euro imitations.


HC-2104 Euro- Clear- The best automotive clear money can buy! Compare to Spies – Glasurit at a fraction of the cost!

A beautiful HIGH GLOSS European style clear. Very High Solids and cures much more quickly than “cheaper” Euro imitations.

HC-2104 European Clear delivers a premium-quality, high gloss finish. HC-2104 offers superior gloss, high build, and outstanding resistance to shrinkage and dieback either air-dry or bake. This is our finest HI-SOLIDS CLEAR (also available in a medium solids version HC-2100 Euro Clear).  This is made from the finest European Resins imported to America and is equal to or even superior to ANY clear made at ANY price. Like all of our PREMIER SERIES clears, we use the maximum amounts of 2 UV absorbers!


Mix Ratio:
HC-2104 Eurpean Clear                                       2
HH-7603/5/7 Activator                                        1
HH-7605- Standard
HH-7607- Slow
HR-1360/70/80/90 10-15%   USE  ONLY  Tamco HR Series reducers which are guaranteed moisture free!  Moisture in reducers will kill this product’s shine 100% of the time!

Pot Life

2 hours at 70F
Gun Setups:


Siphon Feed: 1.3 mm – 1.6 mm (0.050” – 0.063”)
Gravity Feed: 1.3 mm – 1.6 mm (0.050” – 0.063”)


Siphon Feed: 1.3 mm – 1.6 mm (0.050” – 0.063”)
Gravity Feed: 1.3 mm – 1.6 mm (0.050” – 0.063”)

Air Pressures

Conventional  Panel Overall
Siphon Feed: 45-55 psi at the gun 45-55 psi at the gun
Gravity Feed: 45-55 psi at the gun 45-55 psi at the gun

HVLP 8-10 psi at the gun.

1.    Allow basecoat to dry 15-30 minutes – 30 minutes if applying multiple coats of pearl or if shop is below 70F.
2.    Apply 2 medium-wet coats of HC-2104 with 15-20 minutes flash between coats.
3.    Do not apply more clear after 2 hours from completion.
4.    HC–2104 is a water “white” clear!
5.    This product “flows” and you will see it level off by itself. The slower the reducer, the greater the leveling.
6.    Can be easily buffed if Tamco BLENDED HARDENERS are used (7600 series)
7.    Can be baked at 140 for 30-40 minutes and is 90% cured (to buff or deliver) see below for more
Flash/Dry Times (Air Dry):
Flash Between Coats: 10 minutes
Dust Free: 60 minutes
Time to Assemble Overnight
Time to Polish Overnight
Time to Stripe Overnight
Time to Deliver Overnight
Time to Decal 48 hours
Flash/Dry Times (Bake @ 140F):
Flash Before Bake 0-5 minutes
Cycle Time 30 minutes at 140F metal temperature
Dust Free At cool down
Time to Assemble At cool down
Time to Polish 20 minutes after cool down
Time to Stripe 20 minutes after cool down
Time to Deliver At cool down
Optimum Times: Air Dry: Overnight @ 70F; Bake: 20 minutes after cool
Sanding: Use 1500 grit or finer or use 1500 DA or finer
Compounding: Use finishing compound. Apply a thin ribbon of material to the
area to be polished. Use a double sided wool pad or a foam
pad. Maintain air polisher or variable speed polisher at 1800-
3000 rpm. Remove excess finishing compound with a clean
soft cloth prior to applying finishing polishing.


Understanding Tamco Clears:

In today’s world, we are confronted with terms that try to trick us to buy something. For example “NO ADDED SUGAR” simply means that they used high naturally occurring sugars that are often higher in sugar and calories thiamin if they simply added sugar in the first place.  REDUCED FAT– Again there is no legal definition of this. If a product has had fat removed it will often have something added, for example sugar and thickening agents. FRESH, PURE OR NATURAL Consumers should be wary because such marketing terms are not defined in law and, if used inappropriately, can confuse and mislead.

This same use of terms by paint companies are used to fool the masses into “junk science” and downright lies.  For example:

Polyurethane: Some companies say that their clears and paints are superior because it is a polyurethane, not just a urethane. “poly” means more than one, and “urethane” means A synthetic crystalline compound, CO(NH2)OC2H5
Therefore a “polyurethane” is a class of synthetic materials made by copolymerizing an isocyanate and a polyhydric resin. Simply put, any two part urethane IS A POLYURETHANE!

Now what you may not know there are three basic types of polyurethanes used in the paint business. They are:

Enamel polyurethanes: Enamel resins cross-linked with a polyisocyanate (usually an IPDI polyisocyanate – a less durable form) which is usually the cheapest and less desirable of all polyurethanes. Usually when people boast that their products are polyurethanes, they are simply cheap enamels crosslinked with a hardener and are NOT all that durable. BEWARE

Acrylic polyurethanes: Very durable coatings, the backbone of the OEM car industry. 100% acrylic polyurethanes have high gloss, and very high gloss retention when exposed to the sun’s UV.  They will stay shiny for many years. They have a good to excellent chemical resistance as well. There are many forms of acrylic resins. Some with mediocre long term durability, and some with outstanding 20 plus year durability.

Linear polyester polyurethanes: The most durable coatings for chemical resistance. VERY HIGH initial gloss, but will loose much of that gloss over a ten year period.  The outstanding chemical resistance is why this type of paint is usually used on large boats and airplanes. The down side of this product is that it cures VERY SLOWLY and hence most would not use these products in the car refinish process.

BLENDS:  Beware! Many clears and paints on the market are actually blends of enamel resins and acrylic resins. This is done for two reasons. One is ease of application (enamels are easier to paint, keep a beautiful “wet edge” and has outstanding initial gloss (upward to 99%!)  However, Tamco does NOT blend our clears with enamels. We use 100% acrylic resins. Why? When enamels are blended into the clear, all of the advantages of initial gloss, are lost within 1 year!  They do not stand up to UV sun radiation much.

Proper additive package:  Most every paint companies know which resins are out there. The real “secret” to this industry is in the formulation of those resins. In the formula of any clear there will be 2 UV’s (if they are good!), 3-5 solvents (for an even evaporation rate), tin additives (to make the paint cure better and quicker) and leveling, or flow agents. These are often heavily guarded secrets in any paint formulations. Tamco after years of testing and experience uses an array of flow agents and other additives. Some are the same used by everyone, others are those we have discovered over years of testing different product additives. OUR CLEARS lay down like glass! That is a nature of the resins we use (we often blend many acrylic resins in just one clear for many different attributes), and the flow additives we have chosen!  Most of our customers are amazed with the look of our clears!  That’s in the additives!  Now some of our spot and repair clears are meant to duplicate factory orange peel (like our HC7600, HC7642 and HC2000), but our glamor clears stand in a league by themselves.

HELP LINE:  When you call us – you get us very quickly, and you will talk with someone who knows their products.  This is a family run business and everyone has many years of experience.  Most of the time you will talk with the owner Tammy Miller. 1-800-678-1533, rings to her cell. She has been making paint with her dad since she was a child!  Bob Barney (her father) has been in the paint business since 1979 and has manufactured and sold marine paints (topside and bottom paint), Industrial finishes and auto refinish paints. You can trust our experience.  Tammy’s husband Sean Miller, is our head tech man. He also runs the paint plant. He has many years of painting experience, from production auto repairs to custom artwork. Sean has painted about every product on the market. He knows what paints do, and how to correct problems that arise.

Tamco CLEAR UV :
Amerflint II — Duraflint II — and No Wax Clears: PRO:   Easy to apply – HIGHEST possible gloss (98-99%) LONGEST GLOSS retention (only 3% in 5 years).  I have made this product for 30 years – I have cars in Florida painted in the 80’s, that still look GREAT!  For many years, all Norfolk Southern locomotives used this product!  John Deere (at the factory) uses this resin, modified by Sherwin Williams with their other resins.
CON: Does Not buff well at all, unless you really know what you are doing.  If you aren’t going to buff- these are great clears.  PLUS or MINUS:   SLOW DRYING

HC-2104 High Solids Euro Clear (Compare to Spies). PRO:  Very High gloss (97-98). Less than a 2% loss of gloss per year. Easily a 7-10 year “real life” coating.  Very Easy to buff. Can adjust dry times with 3 different temp hardeners (fast med slow).  Great Euro look.

CONS: (which is a plus for very experienced painters) VERY HIGH SOLIDS. Do it yourselfers often have problems with these High Solids clears

HC-2100 (EURO CLEAR):– Same product as above- 20% LOWER SOLIDS. All the pluses of 2104, without any cons.  Best selling clear we have.. This is also selling as our COLORMAX 2:1 Euro Clear

HC-2020 HC2021 HC2002 – Great clears ONLY for those used to applying PPG high solids clears!

HC4100 –  This is basically HC-2100, slightly higher solids at a 4:1 ratio.  Our second best selling clears. Easy to apply, very high gloss and gloss retention

Our 2000, HC-7600, HC7642 and other 4:1 Clears  (including the 4:1 Colormax 2000).  PROS:  Easy to apply, 94-95% gloss. Uses a resin system that is almost impossible to fail (in fact 85% of all auto clears are based on this resin). Can be made to dry VERY FAST (for spot repairs).. 3 different temp hardeners (fast med slow)– the same hardeners that are used in the HC-2100 Euro Clears!  These are very popular clears. 100% acrylic urethane- NO ENAMELS added (like most lower cost clears- that looks great when sprayed but dies by 20% in 2 years!)  Our clears in this group looks great for 5-7 years (with a 2-3% loss of gloss per year in Florida testing. BUFFS GREAT!

CONS: a bit lower gloss (95%) vests the other clears, but if buffed has the same gloss as our other clears!  Needs more coats (lower solids except for the HC7642) and use a less durable resin than our premium clears. These products are meant to be used for production clears that will have a good long life and good gloss retention!

ALL OF TAMCO CLEARS have the MAX of 2 UV’s…!!! We do not leave UV out of our less expensive clears…. Many companies DO!

All of Tamco clears use the very expensive BLENDED HARDENERS. (HDT, HDB and IPDI resins)for long life, max. durability and EZ Buffing! Almost nobody does this anymore!!! We still doSee page 6 in this link on why blended hardeners are important:   but not used much anymore by most modern paint companies! We blend all three! HDB, HDT, AND IPDI!

We use ONLY “urethane grade solvents.” in all our products. Only big time companies do this – most generics DO NOT



There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Choose Your Hardener

HH-7603-Fast, HH-7605- Standard, HH-7607- Slow

SKU: HC-2104 2:1 Euro Clear Category: